BMW fault code 5E03
Dynamic stability control
In the dynamic stability control, code 5E03 means different things depending on the version of the module in the car. Find your car below; the app shows the right one for yours.
DSC: Control module, internal (DSC-ECU ECU-internal General error of valve driver status or control detected by cyclic valve relay)
Module versions: Dynamic Stability Control DSC8 Plus (DXC8_P), Dynamic Stability Control DSC8 Plus (DXC_90)
In: 1 Series (E87) 2004–2011, 1 Series (E82) 2007–2013, 1 Series (E81) 2007–2011, 1 Series (E88) 2008–2013, 3 Series (E91) 2005–2012, 3 Series (E90) 2005–2012, 3 Series (E92) 2006–2013, 3 Series (E93) 2007–2013, 5 Series (E60) 2003–2010, 5 Series (E61) 2004–2010, 6 Series (E63) 2003–2010, 6 Series (E64) 2004–2010, X1 (E84) 2009–2015, X5 (E70) 2006–2013, X6 (E71) 2008–2014, X6 (E72) 2009–2011, Z4 (E89) 2009–2016
DSC wheel RPM sensor rear right - short circuit
Module version: Stability system EBC_450 (DSC_56)
Which BMWs have this version depends on the engine and equipment, so we don't list them here; AutoLingo for BMW reads which version your car has.
DSC: Control module, internal (DSC-ECU ECU-internal General error of valve driver status or control detected through cyclic valve relay)
Module version: Dynamic stability control DSC8 (DSC_60)
In: 5 Series (E60) 2003–2010, 5 Series (E61) 2004–2010, 6 Series (E63) 2003–2010, 6 Series (E64) 2004–2010
DSC: End-of-line test: replace control module (tire end test yaw rate sensor)
Module version: Dynamic stability control MK60 (DSC_87)
In: 1 Series (E87) 2004–2011, 1 Series (E81) 2007–2011, 1 Series (E82) 2007–2013, 1 Series (E88) 2008–2013, 3 Series (E90) 2005–2012, 3 Series (E91) 2005–2012, 3 Series (E92) 2006–2013, 3 Series (E93) 2007–2013, 5 Series (E60) 2003–2010, 5 Series (E61) 2004–2010, 6 Series (E63) 2003–2010, 6 Series (E64) 2004–2010, X1 (E84) 2009–2015, X5 (E70) 2006–2013, X6 (E71) 2008–2014, X6 (E72) 2009–2011, Z4 (E89) 2009–2016
DSC: Control module, internal
Module version: Dynamic stability control EHB3 (DXC_70)
In: 1 Series (E87) 2004–2011, 1 Series (E81) 2007–2011, 1 Series (E82) 2007–2013, 1 Series (E88) 2008–2013, 3 Series (E91) 2005–2012, 3 Series (E90) 2005–2012, 3 Series (E92) 2006–2013, 3 Series (E93) 2007–2013, X1 (E84) 2009–2015, X5 (E70) 2006–2013, X6 (E71) 2008–2014, X6 (E72) 2009–2011, Z4 (E89) 2009–2016
Reading and clearing it
Fault code 5E03 is a BMW code, stored in the car's dynamic stability control, not a generic OBD2 code (P0xxx): a generic OBD2 reader only reaches the engine's emissions faults, so it won't show it. AutoLingo for BMW reads it with BMW's own diagnostic protocols, in plain English, with the details the module stored about it, and clears it after a repair. If a fault comes right back after it's cleared, the problem is still there.
The dynamic stability control is on: 5 Series (E60), 5 Series (E61), 6 Series (E63), 6 Series (E64), 7 Series (E65), 7 Series (E66), 7 Series (E67), X5 (E70), X6 (E71), X6 (E72), 1 Series (E81), 1 Series (E82), X1 (E84), 1 Series (E87), 1 Series (E88), Z4 (E89), 3 Series (E90), 3 Series (E91), 3 Series (E92), 3 Series (E93)
Coming soon
Enter your email address to hear when AutoLingo for BMW is ready.